Issued: 26/09/2016 www.radicigroup.com/plastics - info.plastics@radicigroup.com
The information provided in this documentation corresponds to knowledge of Radici Gr ...
Read moreIssued: 26/09/2016 www.radicigroup.com/plastics - info.plastics@radicigroup.com
The information provided in this documentation corresponds to knowledge of Radici Group Performance Plastics on the subject at the date of its publication. This information may be subject to revision as new
knowledge and experience become available. The data provided reflects the average values of the properties measured over an adequate number of different production cycles and relates only to the designated
material; this data may not be valid for such material used in combination with any other materials or additives or in any process, unless expressly indicated otherwise. The data provided should not be used to establish
specification limits nor used alone as the basis of design; it is not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular
purposes. Since Radici Group Performance Plastics cannot anticipate all variations in actual end-use conditions Radici Group Performance Plastics makes no warranties and assumes no liability in connection with any
use of this information. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any patent rights.
Page 1/ 2
PRODUCT INFORMATION
TORZEN T3000HS1L NC01
Material Code Colour Code
DESCRIPTION
PA66 injection moulding grade. Toughened, heat stabilized. Natural colour.
Suitable for parts requiring excellent impact resistance and improved surface appearance. Good properties
retention after ageing.
ISO 1043 : PA66-IT
MATERIAL HANDLING AND PROCESSING
The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water
content for best processing is 0.15%. Typical conditions with a desiccant drier: temperature 80 ° C, dew
point -20 ° C or below, time 2-4 h or more.
Special care must be taken to avoid moisture absorption and contamination with other polymers when
adding regrind material. Colour variation and mechanical properties reduction may occur and should always
be carefully monitored.
Processing Parameters
Melt Temperature: Mold Temperature: Injection Speed:
270 ÷ 290 °C 70 ÷ 90 °C Medium
PRODUCT SAFETY AND APPROVALS
For safety instruction please refer to Material Safety Data Sheet
RoHS compliant 2011/65/UE and following amendments
Issued: 26/09/2016 www.radicigroup.com/plastics - info.plastics@radicigroup.com
The information provided in this documentation corresponds to knowledge of Radici Group Performance Plastics on the subject at the date of its publication. This information may be subject to revision as new
knowledge and experience become available. The data provided reflects the average values of the properties measured over an adequate number of different production cycles and relates only to the designated
material; this data may not be valid for such material used in combination with any other materials or additives or in any process, unless expressly indicated otherwise. The data provided should not be used to establish
specification limits nor used alone as the basis of design; it is not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular
purposes. Since Radici Group Performance Plastics cannot anticipate all variations in actual end-use conditions Radici Group Performance Plastics makes no warranties and assumes no liability in connection with any
use of this information. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any patent rights.
Page 2/ 2
TECHNICAL DATA SHEET
PROPERTY STANDARD UNIT VALUE
DAM* Cond**
Physical Properties
Density ISO 1183 Kg/m3 1070
Moulding shrinkage – Parallel / Normal //*** ISO 294-4 % 1,7-2,0 / 1,6-1,9
Mechanical Properties
Stress at Yield 50mm/min ISO 527-2/1A MPa 47
Yield Strain 50mm/min ISO 527-2/1A % 4,5
Nominal Strain at Break 50mm/min ISO 527-2/1A % 50
Flexural Modulus 2mm/min ISO 178 MPa 1900
Charpy Impact Strength +23°C ISO 179/1 eU kJ/m2 NB
Charpy Impact Strength -30°C ISO 179/1 eU kJ/m2 NB
Charpy Notched Impact Strength +23°C ISO 179/1 eA kJ/m2 82
Charpy Notched Impact Strength -40°C ISO 179/1 eA kJ/m2 19
Izod Notched Impact Strength -30°C ISO 180/1 eA kJ/m2 17
Thermal Properties
Melting Temperature 10°C/min ISO 11357-1-3 °C 262
Heat Deflection Temperature 1.8 MPa ISO 75/2 A f °C 61
Heat Deflection Temperature 0.45 MPa ISO 75/2 B f °C 148
*DAM = Dry As Moulded state **Cond = Conditioned state similar to ISO 1110 ***Melt Temp [°C] / Mold Temp [°C] / Cavity press [MPa]
TORZEN T3000HS1L NC01
Material Code Colour Code
Show less